MIC6315 Open-Drain P Reset Circuit General Description Features The MIC6315 is an inexpensive reset generator circuit that monitors power supplies in microprocessor-based systems. * Precision voltage monitor for 3V, 3.3V, or 5V power supplies * /RESET remains valid with VCC as low as 1V * 5A supply current * 20ms, 140ms, or 1100ms minimum reset pulse widths available * Manual reset input * Available in 4-pin SOT-143 package The function of this device is to assert a reset if either the power supply drops below a designated reset threshold level or /MR is forced low. Several different reset threshold levels are available to accommodate 3V, 3.3V, or 5V powered systems. The MIC6315 has an active low, open-drain /RESET output. The reset output is guaranteed to remain asserted for a minimum of either 20ms, 140ms, or 1100ms after VCC has risen above the designed reset threshold level. The MIC6315 is available in a 4-pin SOT-143 package. Datasheets and support documentation are available on Micrel's web site at: www.micrel.com. Applications * * * * * Portable equipment Intelligent instruments Critical microprocessor power monitoring Printers/computers Embedded controllers Typical Application Micrel Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel +1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com October 17, 2014 Revision 2.0 Micrel, Inc. MIC6315 Ordering Information (1, 2) Part Number (3) Marking Nominal VTH (V) Minimum tRST (ms) Operating Temperature Range Package Lead Finish MIC6315-26D2UY NY 2.63 20 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-29D2UY NM 2.93 20 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-30D2UY N2 3.00 20 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-31D2UY NF 3.08 20 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-40D2UY NW 4.00 20 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-41D2UY N6 4.10 20 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-44D2UY NG 4.38 20 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-46D2UY NQ 4.63 20 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-26D3UY NR 2.63 140 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-29D3UY NP 2.93 140 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-30D3UY N3 3.00 140 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-31D3UY NU 3.08 140 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-40D3UY N8 4.00 140 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-41D3UY N5 4.10 140 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-42D3UY 05 4.20 140 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-44D3UY NH 4.38 140 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-46D3UY NX 4.63 140 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-26D4UY NS 2.63 1100 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-29D4UY NN 2.93 1100 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-30D4UY N4 3.00 1100 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-31D4UY 2N 3.08 1100 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-40D4UY M9 4.00 1100 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-41D4UY M7 4.10 1100 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-44D4UY NJ 4.38 1100 -40C to +85C 4-Pin SOT-143 Pb-Free MIC6315-46D4UY NZ 4.63 1100 -40C to +85C 4-Pin SOT-143 Pb-Free Note: 1. Ship format Tape and reel only (ordering part number add space TR example. MIC6315-26D2UY TR). 2. Standard reel quantity is 3000 pieces. Reel diameter 7in. / Hub diameter 2in. / Width 8mm. 3. Underbar symbol ( _ ) may not be to scale. October 17, 2014 2 Revision 2.0 Micrel, Inc. MIC6315 Pin Configuration 4-Pin SOT-143 (U) (Top View) Pin Description Pin Number Pin Name 1 GND 2 /RESET 3 /MR Manual Reset Input: A logic LOW on /MR forces a reset. The reset will remain asserted as long as /MR is held LOW and for one reset timeout period after /MR goes HIGH. This input can be shorted to ground via a switch or be driven by TTL or CMOS logic. Float if unused. 4 VCC Power Supply Input. October 17, 2014 Pin Function IC Ground. /RESET goes low if VCC falls below the reset threshold and remains asserted for one reset timeout period after VCC exceeds the reset threshold. 3 Revision 2.0 Micrel, Inc. MIC6315 Absolute Maximum Ratings(4) Operating Ratings(5) Terminal Voltage (VCC, /RESET). ..................................... -0.3V to +6.0V (/MR) ............................................ -0.3V to (VCC + 0.3V) Rate-of-Rise (VCC) ................................................. 100V/s Input Current (VCC, /MR) ............................................ 20mA Output Current (/RESET) ............................................ 20mA Lead Temperature (soldering, 10s) ............................ 300C Storage Temperature (TS) ......................... -65C to +150C (6) ESD Rating .................................................................. 3kV Input Voltage (/RESET).................................... GND to 5.5V Operating Temperature Range ................... -40C to +85C Junction Temperature (TJ) ........................ -40C to +125C Power Dissipation (TA = +70C) ............................... 320mW Electrical Characteristics For typical values, VCC = 2.5V to 5.5V; TA = +25C, bold values indicate -40C TA +85C, unless noted. Symbol Parameter VCC Operating Voltage Range ICC Supply Current VTH Reset Voltage Threshold tRST VOL Reset Timeout Period /RESET Output Voltage /RESET Output Leakage Condition Min. 1 VIL /MR Input Threshold Units 5.5 V 5 15 VCC = 3.6V, no load. 5 10 VTH - 2.5% VTH VTH + 2.5% D2U 20 28 44 D3U 140 200 320 D4U 1100 1500 2500 Note 7 VCC 4.0V, tSINK = 3.2mA 0.4 VCC 2.5V, tSINK = 1.2mA 0.3 VCC 1.0V, tSINK = 50A 0.3 1 /RESET de-asserted 10 /MR-to-Reset Delay /MR Input Threshold Max. VCC = 5.5V, no load. /MR Minimum Pulse Width VIH Typ. 2.3 VTH < 4.0V 0.7 x VCC VTH < 4.0V 0.25 x VCC /MR Glitch Immunity V A V 0.8 10 ms s VTH > 4.0V /MR Pull-Up Resistance V s 0.5 VTH > 4.0V A 20 100 30 V k ns Notes: 4. Exceeding the absolute maximum ratings may damage the device. 5. The device is not guaranteed to function outside its operating ratings. 6. Devices are ESD sensitive. Handling precautions are recommended. Human body model, 1.5k in series with 100pF. 7. Various reset thresholds available. See Ordering Information or contact factory. October 17, 2014 4 Revision 2.0 Micrel, Inc. MIC6315 Timing Diagram Functional Diagram October 17, 2014 5 Revision 2.0 Micrel, Inc. MIC6315 Application Information Microprocessor Reset The /RESET pin is asserted whenever VCC falls below the reset threshold voltage or if /MR (manual reset) is forced low. The /RESET pin remains asserted for the duration of the reset timeout period after VCC has risen above the reset threshold or /MR has returned high. The reset function ensures the microprocessor is properly reset and powers up in a known condition after a power failure. /RESET will remain valid with VCC as low as 1V. VCC Transients The MIC6315 is relatively immune to negative-going VCC glitches below the reset threshold. Typically, a negativegoing transient 125mV below the reset threshold with duration of 20s or less will not cause an unwanted reset. If additional transient immunity is needed, a bypass capacitor can be placed a close as possible to the MIC6315. The /RESET output is a simple open-drain N-channel MOSFET structure. A pull-up resistor must be used to pull this output up to some voltage. For most applications, this voltage will be the same power supply that supplies VCC to the MIC6315. It is possible, however, to tie this resistor to some other voltage. This will allow the MIC6315 to monitor one voltage while level-shifting the /RESET output to some other voltage. The pull-up voltage must be limited to 6.0V or less (absolute maximum) to avoid damage to the MIC6315. The resistor must be small enough to supply current to the inputs and leakage paths that are driven by the /RESET output. Figure 1. MIC6315 as Used in a Multiple Supply System /RESET Valid at Low Voltage As VCC drops to 0V, the MIC6315 will no longer be able to pull the /RESET output low. At this point, the pull-up resistor will pull the output high. The value of the pull-up resistor and the voltage it is connected to will affect the point at which this happens. Wire OR'ing the /RESET Output Because the RESET output is open-drain, several reset sources can be wire-OR'ed, in parallel, to allow resets from multiple sources. October 17, 2014 6 Revision 2.0 Micrel, Inc. MIC6315 Package Information and Recommended Landing Pattern(8) 4-Pin SOT-143 (U) Note: 8. Package information is correct as of the publication date. For updates and most current information, go to www.micrel.com. October 17, 2014 7 Revision 2.0 Micrel, Inc. MIC6315 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com Micrel, Inc. is a leading global manufacturer of IC solutions for the worldwide high performance linear and power, LAN, and timing & communications markets. The Company's products include advanced mixed-signal, analog & power semiconductors; high-performance communication, clock management, MEMs-based clock oscillators & crystal-less clock generators, Ethernet switches, and physical layer transceiver ICs. Company customers include leading manufacturers of enterprise, consumer, industrial, mobile, telecommunications, automotive, and computer products. Corporation headquarters and state-of-the-art wafer fabrication facilities are located in San Jose, CA, with regional sales and support offices and advanced technology design centers situated throughout the Americas, Europe, and Asia. Additionally, the Company maintains an extensive network of distributors and reps worldwide. Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this datasheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel's terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2005 Micrel, Incorporated. October 17, 2014 8 Revision 2.0 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Micrel: MIC6315-25D4UY TR MIC6315-26D2UY TR MIC6315-26D3UY TR MIC6315-26D4UY TR MIC6315-29D2UY TR MIC6315-29D3UY TR MIC6315-29D4UY TR MIC6315-30D2UY TR MIC6315-30D3UY TR MIC6315-30D4UY TR MIC6315-31D2UY TR MIC6315-31D3UY TR MIC6315-31D4UY TR MIC6315-40D2UY TR MIC6315-40D3UY TR MIC6315-40D4UY TR MIC6315-41D2UY TR MIC6315-41D3UY TR MIC6315-41D4UY TR MIC6315-42D3UY TR MIC6315-44D2UY TR MIC6315-44D3UY TR MIC6315-44D4UY TR MIC6315-46D2UY TR MIC6315-46D3UY TR MIC6315-46D4UY TR MIC6315-29D4UY-TR MIC6315-30D3UY-TR MIC6315-31D3UY-TR MIC6315-46D3UY-TR MIC6315-31D4UY-TR MIC6315-29D3UY-TR MIC6315-41D4UY-TR MIC6315-30D2UY-TR MIC6315-40D3UY-TR MIC6315-40D4UY-TR MIC6315-29D2UY-TR MIC6315-42D3UY-TR MIC6315-25D4UY-TR MIC6315-46D2UY-TR MIC6315-44D2UY-TR MIC6315-44D3UY-TR MIC6315-44D4UY-TR MIC6315-26D2UY-TR MIC6315-46D4UY-TR MIC6315-26D4UY-TR MIC6315-41D2UY-TR MIC6315-41D3UY-TR MIC6315-40D2UY-TR MIC6315-26D3UY-TR MIC6315-31D2UY-TR MIC6315-30D4UY-TR